임베디드 H/W 설계 ODM · 산업용 LCD/CTP Embedded H/W Design ODM · Industrial LCD & CTP

임베디드 하드웨어,
설계부터 양산까지
한 곳에서 완성합니다
Embedded hardware,
from design to production
in one place

코고스는 NXP i.MX6, Raspberry Pi CM3/CM4, STM32F407 기반 산업용 보드와 7.0″~15.4″ LCD·정전식 터치(CTP) 통합을 전문으로 하는 임베디드 H/W 설계 ODM 기업입니다. RFP 정리부터 회로·PCB 설계, 펌웨어, 인증, 양산까지 단일 창구로 진행합니다. KOGOS is an embedded hardware design ODM specialising in industrial boards built on NXP i.MX6, Raspberry Pi CM3/CM4 and STM32F407, together with 7.0″–15.4″ LCD and capacitive touch integration. One team carries your project from RFP and circuit/PCB design through firmware, certification and volume production.

표준 플랫폼Platforms
5

i.MX6 · CM4 · CM3 · STM32F407i.MX6 · CM4 · CM3 · STM32F407

디스플레이 대응Display support
7.0″–15.4″

LVDS · MIPI · CTP 통합LVDS · MIPI · CTP integration

핵심 인력 경력Core team
15+yrs

H/W · PCB · S/W 개발H/W · PCB · S/W development

KOGOS IMX6Q 보드
IMX6Q Board 2026 ODM Lineup2026 ODM Lineup
Linux4.1.15
3 ×EthernetEthernet

아이디어를 양산되는 제품으로 만드는 엔지니어링 팀 The engineering team that turns ideas into shippable products

코고스(KOGOS)는 산업용 임베디드 보드와 HMI를 설계·공급하는 ODM 전문 기업입니다. 고객의 요구사항을 RFP 단계에서 구체화하고, 회로 설계 · PCB 아트워크 · 펌웨어 · 애플리케이션 · 인증 · 양산을 하나의 팀이 책임집니다. KOGOS designs and supplies industrial embedded boards and HMI systems as an ODM partner. We sharpen a customer's requirement at the RFP stage, then own circuit design, PCB artwork, firmware, application software, certification and production with a single team.

자체 설계한 i.MX6, Raspberry Pi CM3/CM4, STM32F407 플랫폼에 산업용 LCD와 정전식 터치를 통합한 패널 PC · HMI · RTU · 충전기 제어보드를 공급하며, 2026년 기준 ODM 라인업 5종을 표준 제품으로 제공합니다. On our own i.MX6, Raspberry Pi CM3/CM4 and STM32F407 platforms we integrate industrial LCDs and capacitive touch to ship panel PCs, HMIs, RTUs and charger control boards. Five of these are offered as standard products in the 2026 ODM lineup.

소량 시제품부터 양산까지, 부품 수급과 장기 공급 안정성을 함께 고려해 설계합니다. From a handful of prototypes to volume, we design with component supply and long-term availability in mind.

SOMPanel PCHMIRTUGatewayEV Charger

하드웨어부터 양산까지,
한 팀이 담당합니다
From hardware to production,
held by one team

설계와 양산 사이에서 발생하는 커뮤니케이션 비용을 줄이는 것이 ODM의 핵심입니다. 코고스는 기구·전장·펌웨어·인증 담당이 같은 프로젝트에 참여합니다. The point of an ODM is to remove the hand-over cost between design and production. Mechanical, electrical, firmware and certification engineers sit on the same project.

H/W Design ODMH/W Design ODM

회로 설계, PCB 아트워크, 부품 선정, 시제품 제작까지. SoM·베이스보드 설계와 RS-485/CAN/ADC/DAC/GPIO 인터페이스 확장을 수행합니다. Circuit design, PCB artwork, component selection and prototyping, including SoM and base-board design with RS-485, CAN, ADC/DAC and GPIO expansion.

  • 회로 · PCB 아트워크 (멀티레이어)Circuit & multilayer PCB artwork
  • 산업용 인터페이스 설계 (RS-485 · CAN · 절연)Industrial interfaces (RS-485, CAN, isolation)
  • 전원 · EMI · ESD 검토Power, EMI and ESD review

산업용 LCD · CTP 통합Industrial LCD & CTP

7.0″~15.4″ LVDS/MIPI LCD와 I2C·USB 방식 정전식 터치를 보드에 맞춰 통합합니다. 백라이트·광학·기구 조건과 전면 IP65 설계까지 검토합니다. 7.0″–15.4″ LVDS/MIPI panels with I2C or USB capacitive touch, matched to your board, including backlight, optics, mechanics and IP65 front-panel design.

  • 7.0″ / 10.1″ / 15.4″ 표준 대응7.0″ / 10.1″ / 15.4″ standards
  • 터치 글러브·산업 환경 대응 검토Glove and harsh-environment touch review
  • 케이블·커넥터·기구 연동 설계Cable, connector and enclosure design

Turnkey ProductionTurnkey Production

부품 소싱, SMT, 기능 검사, 포장·출하까지 일괄 진행합니다. 소량 시제품과 양산 물량을 같은 공정 기준으로 관리합니다. Component sourcing, SMT, functional test, packing and shipment. Prototype runs and volume builds follow the same process standard.

  • 부품 수급 · 대체품 검토Sourcing and alternate-part review
  • 기능 검사 지그 · 검사 항목 정의Test jigs and test-item definition
  • KC · CE · FCC · UL 인증 진행KC, CE, FCC and UL certification

S/W · 펌웨어까지 같은 팀에서Software and firmware from the same team

Linux(QT) · Raspberry Pi OS · FreeRTOS · Android 기반 펌웨어와 PC/모바일 애플리케이션을 개발합니다. 현장 장비 연동과 원격 모니터링 구성도 함께 설계합니다. Firmware on Linux (QT), Raspberry Pi OS, FreeRTOS and Android, plus PC and mobile applications, including field-device integration and remote monitoring.

  • Linux 4.1 / Buildroot
  • Raspberry Pi OS
  • QT GUI
  • FreeRTOS
  • Android
  • Modbus / RS-485
  • Node-RED

RFP에서 양산까지 5단계Five steps from RFP to volume

  1. 01

    요구사항 정의Requirement

    용도·환경·인터페이스·수량·인증 범위를 정리하고 RFP를 함께 작성합니다.We define use case, environment, interfaces, volumes and certification scope, and write the RFP together.

  2. 02

    플랫폼 매칭Platform match

    보유 플랫폼과 표준 제품 중 가장 가까운 구성으로 일정·원가를 제안합니다.We propose the closest fit among our platforms and standard products, with schedule and cost.

  3. 03

    설계 · 시제품Design

    회로·PCB·기구·펌웨어 설계 후 시제품을 제작해 기능을 검증합니다.Circuit, PCB, mechanical and firmware design, then prototype builds for functional validation.

  4. 04

    검증 · 인증Validation

    환경 시험과 EMC 사전 검토, KC·CE·FCC 등 인증을 진행합니다.Environmental testing, pre-scan EMC review and KC/CE/FCC certification.

  5. 05

    양산 · 공급Production

    양산과 출하 검사, 이후 장기 공급과 변경 관리를 담당합니다.Volume build, outgoing inspection, then long-term supply and change control.

바로 적용 가능한 5개의 플랫폼Five platforms, ready to deploy

표준 사양으로 공급하며, 인터페이스·디스플레이·케이스는 프로젝트에 맞춰 조정할 수 있습니다. 카드를 눌러 전체 사양을 확인하세요. Supplied as standard, customisable on interface, display and enclosure. Open a card for the full specification.

2026 ODM 카탈로그 (PDF)2026 ODM catalogue (PDF)
KOGOS IMX6Q Board — NXP i.MX6 Quad 산업용 메인보드

NXP i.MX6 Quad

IMX6Q Board

3개의 이더넷과 최대 15.4″ LVDS 디스플레이를 지원하는 산업용 메인보드. RS-232/RS-485 선택형 UART와 CAN, mSATA·Mini PCIe 확장을 제공합니다. Industrial main board with three Ethernet ports and up to a 15.4″ LVDS display, selectable RS-232/RS-485 UARTs, CAN, plus mSATA and Mini PCIe expansion.

  • 3 × Ethernet
  • 7.0″–15.4″ LVDS
  • 8 × RS-232 / 2 × CAN
  • Linux 4.1.15
  • 4코어 Cortex-A9 · 2 GB RAM · 32 GB eMMCQuad Cortex-A9 · 2 GB RAM · 32 GB eMMC
  • Mini PCIe(4G) · mSATA SSD 확장Mini PCIe (4G) · mSATA SSD expansion
  • 동작 온도 -20 ~ 70 ℃Operating -20 to 70 ℃
  • USB · SD · eMMC 부팅 선택Boot from USB, SD or eMMC
견적 문의Request quote
KOGOS CM4 Board — Raspberry Pi CM4 기반 HMI 보드

Raspberry Pi CM4

CM4 Board

CM4 기반 HMI·게이트웨이용 베이스보드. 4포트 RS-485/RS-232와 8ch ADC·4ch DAC, M.2 NVMe와 LTE 확장을 갖췄습니다. CM4 base board for HMI and gateway builds, with four RS-485/RS-232 ports, 8-channel ADC, 4-channel DAC, M.2 NVMe and LTE options.

  • 2 × Ethernet
  • 4 × RS-485/232
  • M.2 NVMe · LTE
  • 24 V
견적 문의Request quote
KOGOS CM3 Board — Raspberry Pi CM3 기반 베이스보드

Raspberry Pi CM3

CM3 Board

컴팩트한 CM3 베이스보드. 7.0″/10.1″ LVDS LCD와 CTP, 3개의 USB 호스트를 갖춘 24V 입력 구성입니다. A compact CM3 base board: 7.0″/10.1″ LVDS LCD with CTP, three USB host ports, 24 V input.

  • 1 × Ethernet
  • 3 × USB 2.0
  • 1 × RS-485 / 2 × RS-232
  • 24 V
견적 문의Request quote
KOGOS STM32F407 Solar RTU — 태양광 원격 단말 제어보드

STM32F407

Solar RTU

태양광 원격 단말(RTU)용 제어보드. 4개의 RS-485와 2개의 RS-232, 5분 UPS 기능, 2.4″ LCD와 4키 조작부를 제공합니다. Control board for solar remote terminal units: four RS-485 and two RS-232 ports, 5-minute UPS, 2.4″ LCD and a four-key panel.

  • 4 × RS-485
  • UPS 5 min
  • 2.4″ LCD + 4-key
  • AC 220 V
견적 문의Request quote
KOGOS EV Charger — 전기차 충전기 제어·계량 보드

STM32F407

EV Charger

전기차 충전기 제어·계량 보드. 4개의 RS-485, 12V 도어락 릴레이, 2.4″ 터치 LCD를 갖춘 AC 220V 구성입니다. EV charger control and metering board: four RS-485 ports, 12 V door-lock relay and a 2.4″ touch LCD on AC 220 V.

  • 4 × RS-485
  • 12 V Relay
  • 2.4″ CTP
  • AC 220 V
견적 문의Request quote

※ 표기 사양은 2026 ODM Product List 기준이며, 프로젝트 요구에 따라 커스터마이징이 가능합니다. Specifications follow the 2026 ODM Product List and can be customised per project.

현장에 바로 들어가는 산업용 하드웨어Industrial hardware that goes straight on site

산업 자동화 · HMIFactory automation & HMI

설비 제어반, 패널 PC, PLC 연동 게이트웨이Control cabinets, panel PCs, PLC gateways

에너지 · EV 충전Energy & EV charging

태양광 RTU, 충전기 제어·계량 보드Solar RTUs, charger control and metering

스마트 디바이스Smart devices

터치 단말, 키오스크, 무선 연동 제품Touch terminals, kiosks, connected products

의료 · 계측Medical & instrumentation

진단·계측 장비의 메인보드와 데이터 수집Main boards and data acquisition for diagnostics

통신 · 게이트웨이Connectivity & gateways

RS-485 · CAN · 4G/LTE 기반 현장 수집Field acquisition over RS-485, CAN and 4G/LTE

주문형 제품 개발Custom product development

기존 보드 기반 파생 모델, 소량 맞춤 생산Derivatives of existing boards, small custom builds

프로젝트를 말씀해 주세요.
가능한 구성부터 정리해 드립니다.
Tell us about the project.
We will start from what is feasible.

용도, 수량, 희망 일정, 필요한 인증을 알려주시면 검토 후 회신드립니다. 표준 제품 구매 문의도 환영합니다. Share the use case, volume, target schedule and required certification. Standard-product enquiries are welcome too.

  • E-mail jylee@kogos.co.kr
  • Mobile +82-10-9034-7253
  • R&D Center
    (10544) 경기도 고양시 덕양구 으뜸로 130
    위프라임트윈타워 A동 1112호
    Room 1112, Bldg A, WePrime Twin Tower
    130 Eutteum-ro, Deogyang-gu, Goyang-si, Gyeonggi-do 10544, Korea
  • 담당Contact person 이주용 (Ju Yong Lee)Ju Yong Lee

문의 남기기Send an enquiry

전송을 누르면 기본 메일 앱이 열리고 jylee@kogos.co.kr 로 보낼 내용이 채워집니다. 웹 서버에 저장되는 정보는 없습니다. Submitting opens your mail app with the message addressed to jylee@kogos.co.kr. Nothing is stored on a server.